Vendor: Cisco Exam Code: 200-105 dumps Exam Name: Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) Version: DemoDEMO

QUESTION 1 It has become necessary to configure an existing serial interface to accept a second Frame Relay virtual circuit. Which of the following are required to solve this? (Choose three) A. configure static frame relay map entries for each subinterface network. B. remove the ip address from the physical interface C. create the virtual interfaces with the interface command D. configure each subinterface with its own IP address E. disable split horizon to prevent routing loops between the subinterface networks F. encapsulate the physical interface pass4itsure ciscowith multipoint PPP Correct Answer: BCD

QUESTION 2 Which of these represents an IPv6 link-local address? A. FE80::380e:611a:e14f:3d69 B. FE81::280f:512b:e14f:3d69 C. FEFE:0345:5f1b::e14d:3d69 D. FE08::280e:611:a:f14f:3d69 Correct Answer: A

QUESTION 3 What are the benefit of using Netflow? (Choose three.) A. Network, Application & User pass4itsure microsoft Monitoring B. Network Planning C. Security Analysis D. Accounting/Billing Correct Answer: ACD

QUESTION 4 What is a valid HSRP virtual MAC address? A. 0000.5E00.01A3 B. 0007.B400.AE01 C. 0000.0C07.AC15 D. 0007.5E00.B301 Correct Answer: C

QUESTION 5 Refer to the exhibit.What three actions 200-125 dumps will the switch take when a frame with an unknown source MAC address arrives at the interface? (Select three.) A. Send an SNMP trap. B. Send a syslog message. C. Increment the Security Violation counter. D. Forward the traffic. E. Write the MAC address to the startup-config. F. Shut down the port. Correct Answer: ABC

QUESTION 6 What would be the destination Layer 2 address in the frame header for a frame that is being forwarded by Dubai to the host address of A. 825 B. 230 C. 694 D. 387 Correct Answer: C

QUESTION 7 A network administrator has configured access list 173 to prevent Telnet and ICMP traffic from reaching a server with the address of Which pass4itsure commands can the administrator issue to verify that the access list is working properly? (Choose three.) A. Router# ping B. Router# debug access-list 173 C. Router# show open ports D. Router# show access-lists E. Router# show ip interface Correct Answer: ADE

QUESTION 8 DRAG DROP Select and Place:Correct Answer:

QUESTION 9 Lab - Access List Simulation A network associate is adding security to the configuration of the Corp1 router. The user on host C should be able to use a web browser to access financial information from the Finance Web Server. No other hosts from the LAN nor the Core should be able to use a web browser 210-260 dumps to access this server. Since there aremultiple resources for the corporation at this location including other resources on the Finance Web Server, all other traffic should be allowed. The task is to create and apply a numbered access-list with no more than three statements that will allow ONLY host C web access to the Finance Web Server. No other hosts will have web access to the Finance Web Server. All other traffic is permitted. Access to the router CLI can be gained by clicking on the appropriate host. All passwords have been temporarily set to “cisco”. The Core connection uses an IP address of The computers in the Hosts LAN have been assigned addresses of – Host A Host B Host C Host D The servers in the Server LAN have been assigned 300-115 dumps addresses of – The Finance Web Server is assigned an IP address of The Public Web Server is assigned an IP address of Correct Answer: Check the answer in explanation

QUESTION 10 A sporting goods manufacturer has decided to network three (3) locations to improve efficiency in inventory control. The routers have been named to reflect the location: Boston, Frankfurt, and Lancaster. The necessary networking has been completed at each location, and the routers have been configured with single area OSPF as the routing protocol. The 300-101 dumps Boston router was recently installed but connectivity is not complete because of incomplete routing tables. Identify and correct any problem you see in the configuration. Note: The OSPF process must be configured to allow interfaces in specific subnets to participate in the routing process.Correct Answer: The question mentioned Boston router was not configured correctly or incomplete so we should check this router first. Click on Host B to access the command line interface (CLI) of Boston router.

QUESTION 11 Why did Branch1 router lose WAN connectivity with R1 router?A. The IP address is misconfigured on PPP multilink interface on the Branch1 router. B. The PPP multilink group is misconfigured on the anch1 serial interfaces.   C. The PPP multilink group is misconfigured on the R1 serial interfaces. D. The Branch1 serial interfaces are placed in a 300-075 dumps shutdown condition. Correct Answer: A

QUESTION 12 Which component of the Cisco SDN solution serves as the centralized management system? A. Cisco OpenDaylight B. Cisco ACI C. Cisco APIC D. Cisco IWAN Correct Answer: B

QUESTION 13 Which EIGRP for IPv6 command can you enter to view 210-065 dumps the link-local addresses of the neighbors of a device? A. show ipv6 eigrp 20 interfaces B. show ipv6 route eigrp C. show ipv6 eigrp neighbors D. show ip eigrp traffic Correct Answer: C

QUESTION 14 What is a difference between TACACS+ and RADIUS in AAA? A. Only TACACS+ allows for separate authentication. B. Only RADIUS encrypts the entire access-request packet. C. Only RADIUS uses TCP. D. Only TACACS+ couples authentication and authorization. Correct Answer: A

QUESTION 15 Which IEEE standard does PVST+ use to tunnel information? A. 802.1x B. 802 1q C. 802.1w D. 802.1s Correct Answer: B

QUESTION 16 Which type of interface can negotiate an 300-135 dumps IP address for a PPPoE client? A. Ethernet B. dialer C. serial D. Frame Relay Correct Answer: B

QUESTION 17 Which statement about QoS default behavior is true? A. Ports are untrusted by default. B. VoIP traffic is passed without being tagged. C. Video traffic is passed with a well-known DSCP value of 46. D. Packets are classified internally with an environment. E. Packets that arrive with a tag are untagged at the edge of an administrative domain. Correct Answer: E

QUESTION 18 Refer to the exhibit. Why has this switch not been elected the root bridge for VLAN1? A. It has more than one interface that is 400-101 dumps connected to the root network segment. B. It is running RSTP while the elected root bridge is running 802.1d spanning tree. C. It has a higher MAC address than the elected root bridge. D. It has a higher bridge ID than the elected root bridge. Correct Answer: D

QUESTION 19 Refer to the exhibit.At the end of an RSTP election process, which access layer switch port will assume the discarding role? A. Switch3, port fa0/1 B. Switch3, port fa0/12 C. Switch4, port fa0/11 D. Switch4, port fa0/2 E. Switch3, port Gi0/1 F. Switch3, port Gi0/2 Correct Answer: C

QUESTION 20 Refer to the exhibit. A packet with a source IP address of and a destination IP address of arrives at the AcmeB router. What action does the router take?A. forwards the received packet out the Serial0/0 interface B. forwards a packet containing an EIGRP advertisement out the Serial0/1 interface C. forwards a packet containing an ICMP message out the FastEthemet0/0 interface D. forwards a packet containing an ARP request out the FastEthemet0/1 interface Correct Answer: C

QUESTION 21 Which type of EIGRP route entry describes a feasible successor? A. a backup route, stored in the routing table B. a primary route, stored in the routing table C. a backup route, stored in the topology table D. a primary route, stored in the topology table Correct Answer: C

QUESTION 22 What can be done to secure the virtual terminal interfaces on a router? (Choose two.) A. Administratively shut down the interface. B. Physically secure the interface. C. Create an access list and apply it to the virtual terminal interfaces with the access-group command. D. Configure a virtual terminal password and login process. E. Enter an access list and apply it to 200-150 dumps the virtual terminal interfaces using the access-class command. Correct Answer: DE

QUESTION 23 A network administrator is troubleshooting an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information? A. Router# show ip eigrp adjacency B. Router# show ip eigrp topology C. Router#show ip eigrp interfaces D. Router#show ip eigrp neighbors Correct Answer: D

QUESTION 24 Refer to the exhibit.Assume that all of the router interfaces are operational and configured correctly. How will router R2 be affected by the configuration of R1 that is shown in the exhibit? A. Router R2 will not form a neighbor relationship with R1. B. Router R2 will obtain a full routing table, 210-255 dumps including a default route, from R1. C. R2 will obtain OSPF updates from R1, but will not obtain a default route from R1. D. R2 will not have a route for the directly connected serial network, but all other directly connected networks will be present, as well as the two Ethernet networks connected to R1. Correct Answer: A

QUESTION 25 Refer to the exhibit. How will the router handle a packet destined for The router will drop the packet. B. The router will return the packet to its source. C. The router will forward the packet via Serial2. D. The router will forward the packet via either Serial0 or Serial1. Correct Answer: C

400 Bad Request
400 Bad Request
Please forward this error screen to's WebMaster.

Your browser sent a request that this server could not understand:

  • (none)/orggsds51.txt (port 80)
Thời khóa biểu của hệ CĐLT khóa 40A,B

Thời khóa biểu của hệ CĐLT khóa 40A,B

Read more

Sinh viên đăng ký dự thi tuyển sinh liên thông từ trung cấp lên cao đẳng xem thông báo ( có thay đổi thời gian) dưới đây nhé.

Read more
Thông báo Chương trình “Ngày hội việc làm năm 2017”

Để gắn kết và tạo lập mối quan hệ bền vững giữa Nhà trường – Doanh nghiệp trong việc nâng cao chất lượng đào tạo, đào tạo đáp ứng yêu cầu của thị trường lao động và tạo … xem tiếp

Read more
Trang 1/11

Vendor: Microsoft Exam Code: 70-532 dumps Exam Name: Configuring Advanced Windows Server 2012 Services Version: DemoDEMO

QUESTION 1 Your network contains one Active Directory domain. The domain contains two Hyper-V hosts named Host1 and Host2 that run Windows Server 2012 R2. Host1 contains a virtual machine named VM1. You plan to move VM1 to Host2. You need to generate a report that lists 070-413 dumps any configuration issues on Host2 that will prevent VM1 from being moved successfully. Which cmdlet should you use? A. Move-VM B. Test-VHD C. Debug-VM D. Compare-VM Correct Answer: C

QUESTION 2 You have an enterprise certification authority (CA) named CA1. You have a certificate template named UserAutoEnroll that is based on the User certificate template. Domain users are configured to autoenroll for UserAutoEnroll. A user named User1 has an email address defined in Active Directory. A user named User2 does not have an email address defined in Active 70-463 dumps Directory. You discover that User1 was issued a certificate based on UserAutoEnroll template automatically. A request by user2 for a certificate based on the UserAutoEnroll template fails. You need to ensure that all users can autoenroll for certificated based on the UserAutoEnroll template. Which setting should you configure from the properties on the UserAutoEnroll certificate template? A. Issuance Requirements B. Request Handling C. Cryptography D. Subject Name Correct Answer: D

QUESTION 3 Your organization is deploying a second Active 70-243 dumps Directory forest because a substantial number of users need to access a resource that requires significant changes to the Active Directory schema, which are not compatible with your current forest's schema. You want users in your forest to be able to access any resource in any domain in the new forest. Which of the following should you do to accomplish this goal? A. Configure a forest trust. B. Configure an external trust. C. Create a shortcut trust. D. Configure name suffix routing. Correct Answer: A

QUESTION 4 Your network contains one Active Directory forest named The forest contains two child domains and six domain controllers. The domain controllers are configured as shown in the following table.You need to add an additional UPN Suffix. What should you use? A. Set-ADSite B. Set-ADReplicationSite C. Set-ADDomain D. Set-ADReplicationSiteLink E. Set-ADGroup F. Set-ADForest G. Netdom Correct Answer: F

QUESTION 5 You are employed as a network 70-488 dumps administrator at has an active directory domain named All servers on the network have Windows Server 2012 R2 installed. has a server named server1,which is configured as a file server. You have been instructed to enabled a feature that discovers and eradicates duplication within data without compromising its reliability or accuracy. Which of the following actions should you take? A. You should consider having the Data Deduplication feature enabled. B. You should consider having the Storage Spaces feature enabled. C. You should consider having the Storage Management feature enabled. D. You should consider having the folder redirection feature enabled. Correct Answer: A

QUESTION 6 You want to enable key archiving on a CA. You need to issue a certificate from a specific template to the user who will recover private keys. Which certificate template will you use as the basis for this certificate?A. Kerberos authentication B. Code signing C. OCSP response signing D. Key recovery agent Correct Answer: D

QUESTION 7 You are employed as a senior 70-346 dumps network administrator at has an Active Directory domain named All servers on the network have Windows Server 2012 R2 installed. has two servers,named SERVER1 and SERVER2 which are configured in a two- node failover cluster. Server1 includes a folder,named ABCAppData,which is configured as a Distributed File System (DFS) name space folder target. After configuring another two nodes in the failover cluster, you are instructed to make sure that access to ABC AppData is highly available. You also have to make sure that application data is replicated to ABCAppData via DFS replication. Which following actions should you take ? A. You should consider configuring a scale-out File Server B. You should consider configuring the replication settings for the cluster C. You should consider configuring a file server for general use D. You should consider configuring the Quorum settings Correct Answer: A

QUESTION 8 Your network contains an Active Directory domain named All domain controllers run Windows 70-533 dumps Server 2012 R2. The domain contains two domain controllers. The domain controllers are configured as shown in the following table. The Branch site contains a perimeter network. For security reasons, client computers in the perimeter network can communicate with client computers in the Branch site only. You plan to deploy a new RODC to the perimeter network in the Branch site. You need to ensure that the new RODC will be able to replicate from DC10. What should you do first on DC10? A. Run dcpromo and specify the /createdcaccount parameter. B. Run the Active Directory Domain Services Configuration Wizard.C. Run the Add-ADDSReadOnlyDomainControllerAccount cmdlet. D. Enable the Bridge all site links setting. Correct Answer: C

QUESTION 9 Your network contains an Active Directory 70-534 dumps domain named All domain controllers run Windows Server 2012. One of the domain controllers is named DC1. The DNS zone for the zone is Active Directory-integrated and has the default settings. A server named Server1 is a DNS server that runs a UNIX-based operating system. You plan to use Server1 as a secondary DNS server for the zone. You need to ensure that Server1 can host a secondary copy of the zone. What should you do? A. From Windows PowerShell, run the Set-DnsServerForwarder cmdlet and specify the zone as a target. B. From Windows PowerShell, run the Set-DnsServerSetting cmdlet and specify DC1 as a target. C. From Windows PowerShell, run the Set-DnsServerPrimaryZone cmdlet and specify the zone as a target. D. From DNS Manager, modify the Advanced settings of DC1. Correct Answer: C

QUESTION 10 You have a server named Server1. A Microsoft 70-695 dumps Azure Backup of Server1 is created automatically every day. You rename Server1 to Server2. you discover that backups are no longer created in Azure. You need to backup the server to Azure. What should you do? A. From the Azure Management Portal, upload the Server2 certificae as a management certificate. B. On Server2, run the Start-OBRegistration cmdlet. C. On Server2, run the Add-WBBackupTarget cmdlet. D. From the Azure Management Portal, modify the configuration on the backup vault. Correct Answer: B

QUESTION 11 You have a server named Server1 that runs Windows Server 2012 R2 and uses Windows Server Backup. You need to identify whether 70-698 dumps the backups performed on Server1 support bare metal recovery. Which cmdlet should you run? A. Get-OBMachineSetting B. GetWBVSSBackupOption C. Get-WBPolicy D. Get-OBPolicy Correct Answer: C

sweetpornfree lsgsex hotmomteen sexmag pornotrix porngalleryz fastmobileporn
yoast seo premium free